Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Plano: What to Know First
FAAC gate installation in Plano typically runs between $2,800 and $7,500 for a complete residential swing or slide system, with the operator itself accounting for $1,200 to $3,200 of that figure. We install and service FAAC swing, slide, and barrier operators as an independent provider, which means we answer to you, not to a manufacturer’s service schedule. Most FAAC installations in Plano are completed within one to three days, depending on whether we’re working from an existing gate or starting with new steel. This page is written for Plano homeowners who already own a FAAC motor or a FAAC-equipped gate and need straight answers about installation, failure points, and what the work should cost. Call (972) 236-7089 and a live person will answer, day or night.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 Series (swing) - capacitor failure in Texas heat. The 400’s start capacitor sits inside a housing that bakes in the Plano sun. After four or five summers, the capacitor dries out and the gate will not move off the closed position even though the board powers up. The fix is a direct capacitor replacement and a housing inspection; we photograph the old part before removal so there is no guessing later.
- FAAC 750/760 series (hydraulic slide) - cold-weather hydraulic pressure drift. The 750 is a workhorse, but its hydraulic fluid thickens in cold snaps, which changes the pressure curve and can trip the anti-crush sensor. In Plano, the bigger issue is the opposite: the winter-to-spring temperature swings cause false pressure faults. We adjust the bypass valves to the correct torque signature and document the setting on the job record.
- FAAC E024U control board - relay chatter from voltage sag. The E024U is a solid board, but Plano’s older neighborhoods with long utility runs see voltage sags in summer when every AC unit on the block cycles on. The relay chatters, the gate starts and stops, and the homeowner thinks the motor is dead. We install a voltage monitor and, where needed, a line conditioner so the board sees clean power before we condemn the operator.
- FAAC telescopic slide arms (e.g., on 390 series) - roller wear from Plano’s clay soil movement. The arms ride on nylon rollers that pick up aluminum oxide and fine clay dust. Over time, the rollers grind down and the arm sags, which makes the gate bind. We replace rollers as a set, not one at a time, because a mismatched set chews the new roller in months. Parts-run note: we stock common FAAC roller sets on the truck.
- FAAC S800H barrier operators - spring tension loss after installation. Barrier arms look simple but the tension spring does real work. If the spring is not set to the arm’s actual weight and length, the operator overdraws current and the board’s thermal protection trips. On every FAAC barrier install in Plano, we set the spring with a weight check before we run the first open cycle.
Our FAAC Gate Installation Process
- 1
Site call and load measurement. We measure the gate leaf weight, track or hinge condition, and the available electrical run before we quote anything. A FAAC install on a sagging gate is a future callback; we will not install an operator on a gate that is already fighting the hinges.
- 2
Written quote with line items. You get the parts number, the labor, and the total, in writing, before any tool comes off the truck. No “call for a quote.” The number on the paper is the number on the invoice.
- 3
Parts decision. We use FAAC OEM boards and capacitors where warranty coverage matters, and quality aftermarket equivalents (same electrical ratings) for wear items like rollers, limit switches, and photo-eye lenses. We show you the difference and the cost on the written scope.
- 4
Installation and setup. Mounting, wiring, limit setting, sensitivity tuning, and photo-eye alignment. We follow FAAC’s torque and pressure specs, but we test beyond the minimum: full-open, full-close, obstruction reversal, and a 20-cycle endurance run.
- 5
Documentation and walkthrough. You get a photo log showing the mount, the board, the limits, and the final wiring. We walk you through the release mechanism, the reset procedure, and the warranty terms before we leave.
BeforeAfterWhat FAAC Gate Installation Costs in Plano
Here are honest price ranges for the most common FAAC scenarios we see in Plano, based on what we have charged over the last several years. Prices include labor and standard hardware; the width and weight of your gate are the biggest variables.
- FAAC 400 swing operator, single-leaf, existing gate: $2,800 - $3,600
- FAAC 750 hydraulic slide operator on existing gate: $4,200 - $5,800
- Full driveway swing gate with FAAC 400 and new steel: $5,500 - $7,500
- FAAC S800H barrier arm install (standard 16-24 ft arm): $1,900 - $2,800
- FAAC photo-eye and safety edge upgrades on existing install: $350 - $650 per edge or beam set
What moves the price: gate weight and width (a 20-foot steel swing gate is a different job than a 12-foot aluminum one), concrete work for new posts or pad, distance from the electrical panel, and whether we are replacing an existing FAAC operator or starting from scratch. Free written estimate, every time. Call (972) 236-7089.
Why Plano Homeowners Call Vance Gate Repair Plano for FAAC Work
We are the shop that writes the price down before the work starts, and then photographs what we did before we leave. Every FAAC install we touch gets a documented photo record: the mount, the board, the wiring, the final limit setting. That record is yours. If something goes wrong within 365 days, we make it right, no argument, no fee - that is the Done Right Promise and it applies to every FAAC job we complete.
We service nine automation brands - LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule - so if your property has a mixed setup, or you switch brands later, we do not need to hand you off to another company. Adrian Vance has been running gate calls across Plano since 2014, and the technicians dispatched to your job are background-checked, uniformed, and named before they arrive. We are independently owned and operated, and we are not a franchise.
FAQs
Yes. Every FAAC install we complete is covered by the 365-Day Done Right Promise, which means if the installation is not right within one year, we fix it at no charge. FAAC OEM parts carry their own manufacturer warranty, and we handle the warranty paperwork for you.
In most cases, yes. If your gate leaf is square, the hinges or track rollers are sound, and the existing FAAC mount is still solid, we can install a new FAAC operator on the existing gate and save you the cost of new steel. We always measure and test the gate before recommending that route.
New FAAC installation is typically scheduled within two to five business days, depending on parts availability and whether concrete work is needed. If your existing operator has failed and the gate is stuck closed, we prioritize those calls and can often get a technician out the same day to get the gate opening manually while we work up the written quote.
Both, and we tell you which is which on the written quote. We use FAAC OEM control boards, capacitors, and hydraulic components where the manufacturer warranty matters. For wear items like rollers, limit switches, and photo-eye lenses, we use quality aftermarket parts that meet or exceed the FAAC electrical specs, and we document the part number on your job record.
Contact Vance Gate Repair Plano
If you need FAAC gate installation in Plano, or a second opinion on a quote from another company, call (972) 236-7089. We hand you a written price before anyone picks up a tool, and we leave a documented photo record when we are done. Here is what I found. Here is what it takes to fix it. Everything else is just paperwork.
Written by Adrian Vance, Owner, Vance Gate Repair Plano at Vance Gate Repair Plano, serving Plano and nearby areas.