Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Plano Homeowners
Plano Gate Parts & Welding solves the problems that gate motor work and access control can’t touch: a hinge that’s torn loose, a post that’s rusted through at the base, a rail that sags under its own weight. We’re Vance Gate Repair Plano, and since 2014 our founder Adrian Vance has built this company on a commercial access-control habit that residential gate work rarely gets: documentation. Every hinge replacement, custom weld, and roller swap we do in Plano comes with a written price before we pick up a tool, and a photo record of the work before we leave. If your gate drags on the ground, won’t latch, or has a hinge that screams every time the opener fires, call (972) 236-7089. A live person answers, at any hour.
What Our Gate Parts & Welding Service Includes
Hinge Replacement
Gate hinges carry the entire weight of the leaf every time it opens and closes, and on a Plano driveway gate that can be several thousand cycles a year. When a hinge wears, the gate tilts, the motor strains, and the latch stops lining up. We replace worn or broken hinges with the correct weight-rated hardware, align the leaf so the gap is even top to bottom, and photograph the new installation so you have a record of what’s in the ground.
Post Replacement
A steel post that’s rotted at ground level or knocked out of plumb by a vehicle is a structural problem, not a cosmetic one. We remove and replace damaged posts in Plano with the right wall thickness for the gate it’s carrying, and we set it in concrete at the correct depth for the load. The new post gets checked with a level before the concrete cures, and we photograph the stump we pulled out so you can see why it failed.
Rail Repair
The rail is the spine of a cantilever or rolling gate, and a rusted-through section will eventually fold under the weight of the gate. We cut out the failed section, weld in matching new steel, and reinforce the joint where the factory joint was weak. Rail repair on a Plano sliding gate usually means the difference between a $400 weld job and a $4,000 gate replacement, and we’ll tell you which one you actually need.
Custom Welding
Sometimes the part that failed was never manufactured to be replaced: a cracked corner bracket, a hinge tab that tore off the frame, a decorative finial that snapped. Our welders fabricate replacement pieces from raw steel matching the original gauge, and we grind the bead smooth so the repair doesn’t look like an afterthought. Custom welding in Plano is what we do when a parts catalog doesn’t have the answer.
Gate Rollers
Sliding gates ride on rollers, and when a roller bearing seizes the gate starts to chatter, bind, and overload the motor. We replace worn rollers with sealed-bearing units that match the track profile, adjust the height so the gate travels square, and check the track for wear while we’re there. A roller replacement we do in Plano leaves the gate rolling with one-finger pressure, and we photograph the old roller and the new one side by side.
Latch & Lock
A gate that won’t latch is an open invitation, and a lock that half-works will fail at the worst possible time. We replace broken latches, align strike plates, install new locks, and adjust the release hardware so the opener and the lock work together instead of fighting each other. Every latch and lock job we do in Plano ends with a function test and a photo of the new hardware in the closed and locked position.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
Most parts and welding work isn’t brand-specific, but the hardware it connects to is. We work on LiftMaster, FAAC, Elite, and Mighty Mule openers every week in Plano, and that matters because the hinge geometry and latch alignment have to work with the opener’s travel settings and the safety edges. A hinge that’s positioned wrong will burn out a LiftMaster motor in months, and a latch that doesn’t release cleanly will fault a FAAC board. We know where each brand wants its hardware, because we’ve pulled apart enough of them to see the difference.
We stock common parts and hardware for all four brands in our Plano service van, so most hinge, latch, and roller work on those systems gets done in a single visit. And if your gate uses something else entirely, the welding and fabrication side of the job doesn’t care what badge is on the motor. Whether you have a LiftMaster, Mighty Mule, Elite, FAAC, or any other make, we can fix the steel that holds it all together.
BeforeAfterSigns You Need Gate Parts & Welding Right Now
- The gate drags or scrapes the ground. This means a hinge has worn, a post has settled, or a roller has lost its bearing. The motor is carrying the extra friction, and every cycle pushes it closer to failure.
- You can see daylight through a crack in the frame or rail. A crack in steel doesn’t stop moving on its own. It grows with every open-and-close cycle until the gate folds or the crack reaches a hinge point.
- The gate sags visibly at the free end. A sagging gate puts the entire load on the motor side hinge and the latch side post. We see Plano gates where the drop is an inch or more, and that load is actively tearing the steel.
- The latch makes metal-on-metal noise or won’t align. The latch is the canary in the coal mine. If the latch is out of alignment, the hinges or the post already moved. Lubricating a misaligned latch doesn’t fix the cause.
- Rust is flaking off the post or the bottom rail. Surface rust is normal on a Texas gate. Flaking, pitting, and holes are not. The bottom rail is where water sits, and Plano’s clay soil holds moisture against the steel from below.
Any of these conditions gets worse with every cycle. If you’re seeing one, call (972) 236-7089 and describe what the gate is doing. We’ll tell you what’s likely wrong and what a written quote will look like before we even come out.
Our Gate Parts & Welding Process - Step by Step
- 1
Inspection and diagnosis. We start by opening and closing the gate manually with the opener disengaged, feeling for resistance at each pivot point and watching where the movement binds. We measure the gap at the hinge side and the free end, check each hinge with the weight on it, and identify the exact part that failed, not just the symptom.
- 2
Written price and scope. Before we touch a tool, you get a written scope of work and a flat price. The scope names the part, the material, the method, and the alignment we’ll restore. You approve it in writing. No approval, no work. That’s Haven Standard Clause 1, and we’ve never done it differently.
- 3
Parts removal and measurement. We remove the failed part and measure it, checking the new part against the old one for hole spacing, hinge offset, and weight rating. On a custom weld, we take the measurements directly from the gate itself, not from a catalog drawing.
- 4
Installation and alignment. The new part goes in using the same technique a commercial access-control install demands: torque settings checked, gate leveled and square, latch tested through a full cycle. We check the opener travel limits after the hardware is replaced so the motor is working with the new geometry, not against it.
- 5
Documentation and function test. Before we leave, we run the gate through a minimum of five full open and close cycles and photograph everything: the old part, the new part installed, the alignment measurements, and the final function test. You get the photo log and the written record of what was installed. That record is on file if you ever need it again.
All our service calls include a documented photo record at no additional charge, fulfilling Haven Standard Clause 4 (Evidence on every job).
How Much Does Gate Parts & Welding Cost in Plano?
A typical hinge replacement in Plano runs $180 to $420 per hinge, depending on the hinge size, the gate weight, and whether the old hinge tore out part of the frame. Post replacement usually lands between $600 and $1,500 depending on post diameter, wall thickness, and whether we have to cut the old post out of the concrete or can set the new one in a fresh footing. Custom welding runs $150 to $500 for most residential jobs, set by the length of the weld, the steel thickness, and the prep work involved, which is why we explain how much Gate Parts & Welding costs upfront in every written quote. Roller replacement on a Plano sliding gate typically runs $120 to $300 per roller including the bearing and the height adjustment.
What moves the price is usually access: a gate that’s buried in landscaping takes longer to work around than a gate on a flat driveway, and a post set in rock or dense clay takes longer to dig. We quote a flat price, not time and materials, so the price we hand you in writing is the price you pay when the work is done. We don’t add trip charges, we don’t bill for “unexpected complications” that a competent inspection should have found, and a written price means you’ll never open an invoice bigger than the number you approved. A free estimate from our Plano team includes the diagnosis and the number, on paper, before you commit to anything.
Gate Parts & Welding Near Plano - Our Service Area
We run gate parts and welding calls throughout Plano and into Far North Dallas, Allen, Richardson, Frisco, Addison, Murphy, North Dallas, Carrollton, McKinney, Prosper, and Wylie. Most parts and welding jobs in Plano are scheduled within 24 to 48 hours, and we’ll give you a confirmed time when you book. No waiting around for a window. For emergency calls where the gate is stuck open or won’t close at all, we prioritize getting a technician to you the same day. For more on the full range of what we handle, see our home page.
Serving Plano, TX - Our Local Coverage Area
We’re based in the Plano area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Plano
Gate parts and welding covers the mechanical steel components of a gate system: hinges, posts, rails, rollers, latches, and any custom fabrication or repair to the gate frame itself. It’s the work that can’t be fixed by replacing a motor board or adjusting a limit switch, because it deals with the physical structure that carries the gate. In Plano, our parts and welding work is what rescues gates that are sagging, dragging, cracked, or tearing themselves apart.
Most hinge and roller replacements are done in one visit of 1 to 3 hours. Post replacement takes 4 to 8 hours including concrete curing setup, and often requires a return trip the next day to re-check alignment after the concrete has set. Custom welding jobs take 2 to 5 hours depending on the work. We quote a timeframe on your written scope so you can plan around it.
Most residential parts and welding service calls in Plano finish between $150 and $1,500, with hinge and roller work on the low end and post replacement or extensive custom fabrication on the high end. Every job gets a written flat price before work starts, so you know the exact number, not an estimate range. Call (972) 236-7089 and we’ll walk through what the problem likely is and what the realistic price window looks like for your specific gate.
Yes. We service LiftMaster, FAAC, Elite, and Mighty Mule openers, plus BFT, Linear, Viking, Ghost Controls, and DoorKing. The parts and welding work is the same quality regardless of the opener brand, but knowing the opener’s travel settings and safety circuits means we install hinges, latches, and rollers that work in sync with the automation instead of against it.
A live person answers our phone 24 hours a day, seven days a week, including holidays. If your gate is stuck open, stuck closed, or won’t latch, call (972) 236-7089 any time and you’ll speak to a human being, not a voicemail. We prioritize same-day dispatch for Plano customers when the gate is a safety or security issue, and we’ll tell you on the phone what to expect.
Every job we complete is covered by our 365-Day Done Right Promise: if the repair is not right within one full year, we make it right at no additional charge. No argument, no fee, no expiration date within that window. Parts themselves carry the manufacturer’s warranty, and we document which part went in and when so a warranty claim is easy if it ever comes up.
Clear the gate’s travel path and make sure a vehicle isn’t parked where the gate needs to swing or slide. If the gate is on a remote, leave the remote somewhere we can reach it. That’s all. We bring everything else: parts, welding equipment, leveling tools, and the documentation we’ll hand you before we start and when we finish.
Schedule Your Gate Parts & Welding Service in Plano Today
Call (972) 236-7089 for a free, no-obligation estimate from our Plano gate parts and welding team. You’ll get a live person on the line, a straight answer about your problem, and a written price before any work begins. We serve Plano and the surrounding cities with documented, warrantied gate repairs that are right the first time.
Written by Adrian Vance, Owner at Vance Gate Repair Plano, serving Plano and the surrounding area since 2014.