Linear Gate Parts & Welding Nationwide

Linear Gate Parts & Welding in Plano: What to Know First

We supply and install Linear gate parts across Plano, and we weld what other companies would tell you to replace. Most Linear hinge, roller, and rail repairs run between $180 and $480 depending on what the metal is doing and whether we’re fabricating a bracket or refreshing a factory part. You get a written price before we touch anything, and the phone number is (972) 236-7089.

Call (972) 236-7089

This page is for Plano homeowners with a Linear actuator on the post, a Linear board in the box, and a gate that’s sagging, grinding, or pulling bolts out of the post. If you’ve been told you need a whole new gate over a hinge pin, you’re in the right place. We’re an independent Linear service provider, not a factory shop, which means we fix what’s there before we talk about replacing it.

How Linear Products Fail - and How We Fix Them

• Linear SL and SLR swing-gate arms: the clevis pin wears oval before the motor does. We see this constantly in Plano, especially on the older SL series where the arm articulates against a steel pin with no bushing. The gate starts jerking at mid-travel, and the homeowner assumes the actuator is dying. We pull the pin, measure the wear, and either install a fresh pin or weld in a bushing so the new one stays round. That’s often a sub-$200 fix on a gate someone quoted for full replacement.
• Linear LRA slide-gate operators and the Plano track problem. The LRA series uses a chain-and-idler setup that works fine until the track shifts. North Texas soil moves, and a concrete pad that was poured level in 2015 may not be level now. The gate develops a hard spot at the same place every cycle. We check track elevation with a level, shim or re-weld the track brackets where needed, and re-tension the chain. The motor is usually fine.
• Linear APeX and MegaCode receivers: the hinge side fails before the electronics do. Linear’s radio gear is solid; the physical gate is what gives up. We get calls about APeX controllers that work perfectly while the gate sags two inches off the hinge post because both post hinges have rusted through. Plano’s freeze-thaw mornings push moisture into weld crevices and the rust accelerates from the inside. We cut out the old hinge, weld in a new one, and match the original geometry so the actuator travel doesn’t change.
• MegaCode keypad locks and the latch strike, which is always the weak link. The weld on the latch strike plate cracks over time, and with a Linear opener doing the pulling, the gate flexes more than it should at the closed position. You’ll hear the actuator labor the last six inches. We re-weld the strike and reinforce the surrounding tube so the next decade’s cycles don’t re-open the same crack.
• Linear PRO series and the post-that’s-too-thin problem. Several PRO-series swing arms land in Plano driveways where the original post was sized for a manual gate. The torque works the post base and the whole assembly starts to lean. We weld a heavier post in place, or reinforce the existing one with a steel collar, and reset the actuator geometry. The alternative is a new operator every few years, which is money nobody should spend twice.

Our Linear Gate Parts & Welding Process

1. 1
   We come out and look at the gate, not just the part you called about. A hinge failure has a cause: a shifted post, a warped rail, a bad roller that transferred load where it doesn’t belong. We find the cause before we weld anything.
2. 2
   We quote in writing. The scope says exactly what we’re replacing, part numbers where applicable, and whether we’re fabricating or using factory Linear components. The price doesn’t change unless you add work.
3. 3
   We make the parts decision with you. On travel-critical parts like arm clevises and drive sprockets, we prefer OEM Linear when the lead time works. On hinges, gussets, and brackets, quality aftermarket steel is usually the better material. We tell you which is which and why.
4. 4
   We do the structural work first. Hinges, posts, rails, rollers. If the metal isn’t right, any actuator work is wasted. We weld, grind smooth, and paint to match what’s left of the original finish.
5. 5
   We test under load, not just an open-close cycle. We cycle the gate with the operator and watch for bind marks, listen for gear strain, and re-check the limit positions after the structural work. The 365-Day Done Right Promise covers the whole job.
6. 6
   You get the photo log before we leave. What was removed, what was installed, and the final geometry. Filed to your job record and emailed to you.

Before

After

What Linear Gate Parts & Welding Costs in Plano

Here’s the honest range on the Linear work we do most in Plano:

• Gate hinge replacement and re-weld: $180-$420 depending on hinge count and post condition
• Clevis pin and bushing repair on SL/SLR swing arms: $120-$240
• Slide gate track re-level and re-weld brackets: $280-$520 depending on run length and pad condition
• Latch strike plate reinforcement and re-weld: $160-$300
• Post replacement or reinforcement weld: $380-$850 depending on size, depth, and whether the old post needs demo
• Custom bracket or gusset fabrication: $95-$350 per piece, welded in place

What moves the price is access, post condition, and whether we’re working around buried conduit or irrigation. What does not move the price is the mood of the technician. The written quote is the quote. Estimates are free, and there’s no charge to come out and tell you what you’re actually looking at. Call (972) 236-7089.

Why Plano Homeowners Call Vance Gate Repair Plano for Linear Work

A lot of gate companies in Plano would rather sell you a full operator replacement than spend an afternoon with a welder and a can of cold galvanizing spray. We would rather fix the hinge, show you the photo of the old one sheared at the pin, and leave with the gate closing square. That’s the difference between a parts company and a repair company.

We’ve been doing this since 2014, and Adrian Vance built the company on commercial access-control discipline: write down what you found, write down what you did, and photograph both. Every Linear job gets that treatment. The 365-Day Done Right Promise means if the weld fails or the hinge loosens within a year, we come back and make it right. No argument, no invoice. And if your Linear opener develops a board issue while the physical gate is fine, we carry parts and diagnostics for the other major brands on Plano gates too: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. One truck, one tech, the whole problem handled.

FAQs