Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Hinge & Roller Replacement: The Plano Owner’s Guide
We stock and install Linear-compatible hinge and roller replacement parts throughout Plano, with most single-gate jobs running between $180 and $340 installed, including the parts. We carry the common sizes on the truck, so we can usually complete the swap the same day we arrive. What typically brings a Plano owner to this page is a gate that has started dragging, screeching, or sagging at the latch side, and a closer look shows a roller wheel that has gone flat or cracked, or a hinge pin that is visibly wallowed out from years of heat cycles.
Here is what we find on most Linear installations in Plano: the hardware that carries the gate leaf takes more punishment than the motor ever does. The hinges and rollers are what the entire weight of the gate rides on, and in this climate, the combination of summer heat, dust, and the occasional hard freeze expands and contracts the metal until something gives. Usually it is the roller first.
Which Linear Models This Applies To
Linear swing and slide gates use the same hinge and roller hardware across most residential and light commercial lines: the common US Automatic, Patriot, and older Stealth series installations all spec a similar under-mount roller and a weld-on or bolt-on barrel hinge. The part that varies is the weight rating and the wheel diameter. We see 4-inch and 6-inch roller wheels most often on Plano residential gates, with the heavier 8-inch rollers on longer, steel-framed gates. A gate leaf over 12 feet or over 400 pounds needs the larger wheel and a hinge with a thicker pin, and that is a distinction that gets missed on a lot of replacement jobs.
The quickest way to identify what you have is to measure the roller wheel diameter and the diameter of the hinge pin shaft. Linear rollers also have a stamped load rating on the bracket on most models made after 2005. We stock OEM Linear pin-and-roller kits when the bracket is intact, and we offer a quality aftermarket equivalent when the OEM bracket has worn past reuse. One compatibility gotcha we run into in Plano: if someone has already retrofitted a LiftMaster or Mighty Mule arm to a Linear gate, the hinge spacing can have been moved, and the replacement roller needs to match the new geometry, not the original Linear spec. We identify that before quoting anything.
Vance Gate Repair is an independent service provider and is not affiliated with Linear. That matters here because it means we make the parts call based on what the gate actually needs, not on what one brand catalog says should be on it.
Signs Your Linear Hinge & Roller Replacement Is Failing
- The gate scrapes the ground or the track at the far end. The roller wheel has worn flat on one side, dropping the gate leaf a quarter inch or more. In Plano, where the ground shifts between drought and rain seasons, a gate that cleared fine in April will drag by August.
- A metal-on-metal screech when the gate moves. The roller bearing has gone dry and is now grinding. A flat wheel or a seized bearing will force the motor to work harder, and that is how a $40 roller turns into a $400 board repair.
- The gate sags visibly at the latch end. The hinge pin or the hinge barrel is worn. On Linear gate hinges, the pin wears first, and the gate begins to droop toward the latch post. You can usually see daylight through the top hinge gap when this is happening.
- The gate shudders or jerks partway through the open or close cycle. A cracked roller wheel binds when the flat spot hits the rail. The motor is catching, compensating, and surging, which puts strain on the gearbox and the limit switches.
- The gate stops mid-travel and reverses. The obstruction sensor reads the added resistance from the failing hardware as something in the path. This is the classic misdiagnosis: the sensors get blamed, but the roller is the problem.
BeforeAfterReplacement Cost & What’s Included
In Plano, a Linear hinge and roller replacement runs between $180 and $340 for a single swing gate, installed. The spread depends on whether we are replacing the roller wheel only or the hinge assembly as well, and whether the gate is a lighter aluminum leaf or a heavier steel one. Double gates fall between $300 and $600 for both leaves. Whatever the number is, it is written down before we touch anything. Under Haven Standard Clause 1, you get the price in writing, the part numbers listed, and the labor broken out. There is no surprise line item at the end.
| Job type | Installed price range |
|---|---|
| Single swing gate, roller only | $180 - $260 |
| Single swing gate, hinge & roller | $260 - $340 |
| Double swing gate, both leaves | $300 - $600 |
| Slide gate, roller bracket & wheel | $220 - $380 |
The work is covered by our 365-Day Done Right Promise. If the replacement is not right, we make it right within one full year, no argument and no fee. Before we leave, you get a photo log of the old part, the new part installed, and the written record of the part number. Adrian Vance has been working on Plano gates this way since 2014, and the paperwork habit has never left.
DIY or Call Us?
There is a safe version of DIY here, and there is a version we would rather you not attempt. The safe version: check whether the roller wheel has gone flat, whether the hinge pin has visible slop, and whether the gate frame is cracked at the hinge mount. Photograph what you see and call us with that information. The unsafe version is unbolting the gate leaf from the hinge while the gate is under any remaining tension or while the motor arm is still connected. A swing gate leaf can weigh 300 to 600 pounds. If it drops because the last hinge bolt comes out before you are ready, it will not be gentle with your hands or your fence post.
Most Plano homeowners we talk to are comfortable diagnosing the problem and less comfortable holding a steel gate in position while old hardware gets cut off and new hardware gets welded or torqued to spec. That split is fair. Do the inspection, then call (972) 236-7089 and let us do the lift.
FAQs
Plan on 5 to 8 years for the original rollers and 8 to 12 years for the hinges, with Plano’s heat and soil movement pushing most hardware toward the lower end of that range. Rollers fail first because the bearing seals dry out and the Texas dust finishes the job. If your Linear gate is past year six and you are hearing the scrape, start budgeting for the replacement.
No, not in any way that makes financial sense. The bearing inside the wheel is sealed, and once it has gone dry or cracked, the wheel is finished. Rebuilding would cost more in labor than a new wheel. We tell Plano customers this directly: the part is cheap, the labor is the skill, and the replacement is what restores the gate.
Most single-gate Linear hinge and roller replacements take 45 to 90 minutes on site once the gate is secured and the old hardware is off. Double gates or gates with welded hinge plates add time. We carry the common Linear-compatible roller sizes and hinge kits on the truck, along with parts for LiftMaster, Mighty Mule, and Ghost Controls once we know what else is on the gate. Call (972) 236-7089 for a same-visit quote.
We carry the common 4-inch and 6-inch Linear roller wheels, hinge pins, and bracket kits on the truck, and we stock the 8-inch heavy roller for longer steel gates. If your gate takes a less common size or an exact OEM Linear part, we can usually have it within one to two business days. Either way, the price and the timeline are written down before we order anything.
Call for a Written Quote
If your Linear gate is scraping, sagging, or straining, call us at (972) 236-7089 for a free estimate. You will talk to a person, not a voicemail loop. We will ask what you are hearing, give you a written price before any work starts, and leave a documented record of exactly what was installed. Here is what we found. Here is what it takes to fix it. Everything else is just paperwork.
Written by Adrian Vance, Owner, Vance Gate Repair Plano at Vance Gate Repair Plano, serving Plano and nearby areas.