Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Irving, TX
Gate access control in Irving means something different than it does in Dallas or Carrollton. The Las Colinas district packs Fortune 500 corporate campuses and HOA-governed estate communities into a few square miles, which means one gate might log 400 cycles a day while another sits idle for a week. The common failures, the parts that wear, and the way we approach the work all shift. Call us at (972) 236-7089 and we’ll tell you what’s wrong and what it costs before anyone picks up a tool.
Why Irving Homes Are Different
Irving sits on Blackland Prairie expansive clay. That clay shrinks hard during summer droughts and swells after rain, and it moves gate posts more than any other force we deal with. In North Irving and Valley Ranch, where most homes date from the 1970s through the 1990s, we regularly find steel hinges pulled out of square, wood-framed openings that have drifted, and latches that no longer line up because the post itself has leaned. The Las Colinas side is the opposite: powder-coated aluminum and wrought-iron estate gates tied into HOA access systems, often with a facilities manager who needs the gate working before the next shift change. Along the SH-114 and O’Connor Road corridor, slide gates on campus entry points run rack-and-pinion drives and loop detectors that wear far faster than any residential unit. Irving also gets DFW’s periodic ice storms, which seize hinges and burn out operators left in manual override.
Our Main Irving Services
Most calls we take from Irving fall into two categories: a gate that stopped moving, or a gate that needs to be built, hung, and automated properly. Below are the three pages we maintain for Irving specifically.
Gate Repair in Irving
A gate that drags, won’t latch, or trips its motor is usually a symptom of something underneath. In Irving, that something is often the clay soil under the post. We check the hinges, the post plumb, and the operator limits together, because fixing only the visible problem leaves the hidden one untouched. See Gate Repair in Irving for how we diagnose and repair gate failures.
Gate Installation in Irving
Installing a gate in Irving means accounting for soil movement before the concrete is poured. We set posts deeper than the minimum and spec hardware that tolerates the shrink-swell cycle that Blackland Prairie clay brings. Whether it’s a wood-framed yard gate in North Irving or an aluminum estate gate in Las Colinas, the written scope comes before the first post hole. See Gate Installation in Irving for the full process and pricing.
Gate Motor & Opener in Irving
Operators fail for a reason, and in Irving that reason is frequently a gate that was already binding before the motor gave out. Replacing the operator without addressing the bind means replacing it again in a year. We service the motor that’s already on the property rather than steering you toward a full replacement when a limit switch or capacitor is the actual problem. See Gate Motor & Opener in Irving for motor repair, replacement, and automation.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Irving
Gate access control in Irving splits two ways. In Las Colinas, we work on systems where a card reader or keypad controls employee and visitor access at campus entry points, and a failed component means a line of cars at shift change. In the HOA communities around Valley Ranch, access control is more often a keypad or phone entry unit that lets residents in without getting out of the car, and a misconfigured unit means frustrated neighbors and calls to the property manager. The climate adds its own pressure: DFW summers bake electronics mounted in direct sun, and ice storms push hardware that was marginal over the edge. For the full range of access control work we do, see Gate Access Control.
Keypad Entry
Signs you need it
The keypad reads some codes but not others, or it stops responding entirely after rain or a freeze.
What it costs in Irving
Keypad replacement in Irving typically runs $150 to $450 installed, depending on whether the wiring is intact and the housing can be reused.
How we do it
We test the keypad wiring, read the voltage at the control board, replace the unit if it’s failed, and reprogram the codes before we photograph the finished job.
Phone Entry
Signs you need it
The system doesn’t dial out when a visitor presses call, or the call connects but the gate won’t open.
What it costs in Irving
Phone entry repairs run $180 to $500 depending on whether the problem is the board, the antenna, or the carrier service itself.
How we do it
We trace the call path from the unit through the relay, confirm whether the cellular signal is adequate, and replace the failed component rather than the whole system when possible.
What Gate Access Control Costs in Irving
| Item | Typical range in Irving |
|---|---|
| Keypad replacement | $150-$450 |
| Phone entry repair | $180-$500 |
| Card reader replacement | $200-$500 |
Can you service the access control system my HOA already has?
Yes. We work on the equipment that’s already installed rather than insisting on a full replacement. We service systems using Elite, DoorKing, FAAC, and LiftMaster components, among others. If a board or reader can be repaired, we repair it and document what we did.
Do you provide wiring diagrams for the access control work you do?
Every job includes a documented record of what was found, what was changed, and what part numbers went in. That includes wiring notes and photos so the next technician doesn’t have to reverse-engineer the system from scratch. Call (972) 236-7089 to schedule.
Gate Parts & Welding in Irving
Older Irving gates, especially in the 1970s and 1980s North Irving tract neighborhoods, fail at the connection points before the gate itself gives out. Hinges wear, posts heave in the clay, and weld joints crack from years of small misalignments that were never corrected. In Las Colinas, the parts are higher-end but the failure pattern is the same: a weld fractures, a roller binds, a post drifts just enough that the gate drags. For the full parts and welding scope, see Gate Parts & Welding.
Hinge Replacement
Signs you need it
The gate sags toward the latch side and scrapes the ground even when the post is plumb.
What it costs in Irving
Hinge replacement typically runs $100 to $300 per hinge installed, depending on the gate weight and whether the post needs reinforcement.
How we do it
We brace the gate, cut or unbolt the failed hinge, mount the replacement, and set the gate back to level before photographing the alignment.
Post Replacement
Signs you need it
The post leans visibly, the gate latch no longer lines up, or the concrete around the post has cracked and lifted.
What it costs in Irving
Post replacement runs $300 to $800 per post, including digging the old footing, setting the new post with proper depth, and re-hanging the gate.
How we do it
We remove the old post and footing, set the replacement post deeper than the original with concrete mixed for expansive soil, and re-hang the gate once the concrete has cured.
What Gate Parts & Welding Costs in Irving
| Item | Typical range in Irving |
|---|---|
| Hinge replacement | $100-$300 per hinge |
| Post replacement | $300-$800 per post |
| Weld repair | $80-$350 per joint |
Do you weld on-site or take the gate to a shop?
Most residential weld repairs are done on-site, which means the gate never leaves the property and you can see the work before we clean up. Larger or more complex fabrications may go to a shop, and you’ll know that before we start. Call (972) 236-7089 for a written price.
Will you rebuild my existing gate or replace the whole thing?
We rebuild when the gate’s structure is sound and the failure is at the hinges, posts, or weld joints. If the gate frame itself is compromised, we’ll show you the evidence and give you a written price for either option. You decide.
Brands We Service in Irving
We work on the motor that’s already on your property. That includes LiftMaster, FAAC, Elite, and Mighty Mule equipment, plus parts for five other major brands. We stock common boards, remotes, and hardware locally, so many Irving repairs are done same-day. See our brands for the full list.
Pricing for Gate Repair in Irving, TX
| Service | Typical range in Irving |
|---|---|
| Hinge replacement | $100-$300 per hinge |
| Post replacement | $300-$800 per post |
| Weld repair | $80-$350 per joint |
| Keypad replacement | $150-$450 |
| Phone entry repair | $180-$500 |
| Card reader replacement | $200-$500 |
What pushes a price up in Irving is usually what’s underneath: a post that’s heaved in the clay, a gate that was never square, or wiring that’s been patched by hand over the years. The written price you get reflects what we found on the actual gate, and it’s handed to you before any work begins, every time.
Neighborhoods We Serve in Irving
We dispatch technicians to every corner of Irving, from the tract neighborhoods of North Irving through Valley Ranch and the Las Colinas developments. Response time across the city is typically within one business day for scheduled work, with emergency service available when a gate is stuck open or won’t close.
- Valley Ranch
- Las Colinas
- North Irving
- University Hills
- Irving Heights
Service Area - Cities Near Irving
We serve Irving and the surrounding metro area. If you’re in Dallas, TX, Addison, TX, Richardson, TX, or Carrollton, TX, the same written-pricing and documentation standard applies. Dispatch for the DFW area is coordinated from our central office, and crews serve Irving locally.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Irving
Same-day service is available for emergency repairs: a gate stuck open, a gate that won’t close, or an access control failure at a commercial property. Scheduled repairs are typically set within one business day. Call (972) 236-7089 and a live person will answer.
That depends on your HOA’s covenants. In Las Colinas and parts of Valley Ranch, some communities require written approval before a gate’s appearance changes, while most repair work that matches the existing design doesn’t trigger review. We’ll flag what to check, but you’ll want to confirm with your property manager.
The written price covers the full scope: labor, parts, and any adjustments we’ll make while we’re on site. If something changes mid-repair, you get a revised written price before we continue. No invoice surprises at the end. That’s how we’ve done it on every Irving job since the beginning.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Irving Customers Say
"Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.