Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Frisco, TX
Frisco’s gate access control systems fail in a pattern shaped by two forces: the city’s master-planned housing boom and Blackland Prairie clay. Thousands of automated ornamental iron gates installed across Stonebriar, Starwood, and Phillips Creek Ranch between roughly 1998 and 2015 are now reaching the age where keypads, card readers, and intercom boards fail, and where the gate posts themselves migrate out of plumb on shrink-swell soil. We diagnose the post movement first, because in Frisco a keypad that “stopped working” is often a keypad that stopped being able to reach a latch. Call (972) 236-7089 and we’ll send a technician who documents what they find, gives you the written price, and only then starts the repair.
Why Frisco Homes Are Different
Most of Frisco is master-planned, HOA-governed, and built on clay that moves. The housing stock is almost entirely single-family subdivisions constructed from the mid-1990s onward, which means three things for gate work. First, the ornamental iron and powder-coated steel gates specified by the HOAs are aging on a predictable timeline: motors fail between 8 and 12 years, hinges fatigue between 10 and 15, and the powder-coat finishes fade and chalk at different rates depending on sun exposure. Second, the soil itself is the most common underlying cause of a gate that won’t close. Blackland Prairie clay expands noticeably after rain and shrinks in summer drought, and a stone or brick gate pillar can tilt a half inch or more within a single season. That throws swing-gate geometry out of alignment without any mechanical failure, and it is the single most frequent diagnosis on Frisco service calls. Third, the HOAs in communities like Richwoods and Phillips Creek Ranch frequently require matching finishes, specific ornamental styles, and in some cases architectural review before a panel or operator can be replaced. We handle the documentation and the matching, so the repair doesn’t stall at the HOA desk.
Our Main Frisco Services
Frisco homeowners call Vance Gate Repair for two categories of work more than any other: the fast repair of a gate that has stopped operating, and the design and installation of a new gate when a property changes hands or an HOA requires an upgrade. Below are the three most common service pages for this area.
Gate Repair in Frisco
A gate that won’t open, grinds mid-travel, or slams at the end of its arc is a repair call. In Frisco the first question is usually whether the gate itself or the ground under the gate is the cause. Our technicians check the post alignment before touching the motor, because on this clay a gear-strip at the opener is frequently secondary damage from a pillar that shifted. We carry parts for LiftMaster, FAAC, BFT, and Mighty Mule operators, and we document every repair with photos and a written parts list before we leave. Gate Repair in Frisco
Gate Installation in Frisco
New gate installations in Frisco start with the HOA’s design requirements: the finish, color, ornamental pattern, and sometimes the operator type are specified by the association. We fabricate or order to match those requirements, set the posts to a depth that accounts for the expanding clay cycles, and run the power and control wiring before hanging the gate. Every installation is quoted in writing before any material is ordered. Gate Installation in Frisco
Gate Motor & Opener in Frisco
When the gate itself is sound but the operator is dead, we service and replace motors, control boards, arm brackets, and limit switches. In Frisco the dominant motor repair pattern is clay-driven bind, which burns out capacitors and strips gears over time. We photograph the limit-switch settings, the gear condition, and the final alignment so the next technician doesn’t start over from zero. Gate Motor & Opener in Frisco
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Frisco
Gate access control in Frisco means the electronics that decide who gets in: keypads, remote controls, phone entry systems, card readers, and video intercoms. Because most Frisco gates were installed during the city’s explosive late-1990s and 2000s building wave, the access-control hardware on those gates is now at the end of its service life. Add the clay soil problem, and a Frisco access-control failure is often two problems at once: a circuit board that has died and a gate pillar that has drifted far enough to prevent the latch from engaging. Our approach under Gate Access Control addresses both in one visit.
Keypad Entry
Signs you need it
The keypad accepts the code but the gate doesn’t move, or the keypad goes dark after rain.
What it costs in Frisco
Keypad replacement or repair in Frisco typically runs $180-$340, including the part and the service call.
How we do it
We test the keypad’s power feed at the board, measure the antenna reach, and if the keypad itself has failed we replace it with a weather-sealed unit and re-enroll every code.
Remote Control
Signs you need it
The gate opens from the keypad but not from a remote, or the remote only works within a few feet.
What it costs in Frisco
Adding or replacing a remote costs $120-$220 in Frisco, including programming to the existing operator.
How we do it
We test the receiver’s antenna placement, verify the remote’s frequency against the operator’s board, and program the new remote while documenting the receiver’s dip-switch or rolling-code settings.
Phone Entry
Signs you need it
The call goes through but the gate won’t open from the phone, or the system dials but never connects.
What it costs in Frisco
Phone-entry repair in Frisco runs $200-$450, depending on whether the fault is in the relay board or the phone module.
How we do it
We isolate the phone module from the control board, test the relay that trips the opener, and replace whichever side has failed, then photograph the new wiring for the record.
Video Intercom
Signs you need it
The video feed is blank, or the audio works but the door/gate release button doesn’t respond.
What it costs in Frisco
Frisco video intercom work generally falls between $250 and $550, including the new monitor or camera unit when one is required.
How we do it
We check the power supply, the camera’s lens and feed, and the release relay in order, then replace only the failed component and photograph the finished connection.
What Gate Access Control Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Keypad replacement or repair | $180-$340 |
| Remote control addition or replacement | $120-$220 |
| Phone entry system repair | $200-$450 |
These are the written ranges we quote before any appointment - the exact number depends on the brand of operator already on the gate and whether the clay-movement issue is present. You’ll always get the price in writing before work starts, under Haven Standard Clause 1.
Can you fix a Frisco keypad the same day you’re called?
Yes, in most cases. We carry keypads for LiftMaster, FAAC, and Mighty Mule on the truck, and a live person answers the phone 24/7 at (972) 236-7089 to schedule the dispatch.
Does Frisco HOA architectural review delay access-control repairs?
Usually not. Keypad and intercom swaps rarely require HOA approval because the gate’s exterior appearance doesn’t change. When a panel-mounted reader or camera housing is involved, we document the match for the HOA file.
Gate Parts & Welding in Frisco
Gate parts and welding in Frisco is the work that keeps an aging ornamental iron gate on its hinges and square to its posts. The problem here is compounded by the Blackland Prairie clay, which tilts pillars and wrenches hinge pins into fatigue; a gate that still looks fine from the curb may be carrying a half-inch of frame twist that no amount of operator adjustment can solve. We start by measuring the gaps and the sag at the hinge side, then we cut, shim, weld, and reinforce exactly what has failed. See Gate Parts & Welding for the full scope of what we fabricate and repair.
Hinge Replacement
Signs you need it
The gate sags at the latch side, the hinge pins are visibly worn, or the gate scrapes the ground on the swing arc.
What it costs in Frisco
Hinge replacement on a Frisco ornamental iron gate typically runs $150-$400 per hinge, including the weld-in or bolt-in labor.
How we do it
We unload the gate weight, cut out the failed hinge, position the new one to restore the original swing plane, and weld or bolt it in before photographing the final weld.
Post Replacement
Signs you need it
The gate post leans visibly, the latch no longer lines up, or the post twists when the gate moves.
What it costs in Frisco
Post replacement in Frisco runs $700-$1,800, depending on the post size, whether it is set in concrete or stone, and whether the pillar masonry must be reworked.
How we do it
We set the new post on a concrete footer deep enough to ride the clay shrink-swell cycle, plumb it with a level, and weld or bolt the gate back to its original geometry.
Custom Welding
Signs you need it
A finial is snapped after an ice storm, a panel bar has cracked, or a section of ornamental scrollwork has broken loose.
What it costs in Frisco
Custom welding repairs in Frisco run $100-$250 per hour plus materials, with a typical repair bill between $250 and $600.
How we do it
We match the rod or bar profile to the existing gate, prep the joint, weld it hot, and then apply a matched powder-coat touch-up or send the section for a full refinish match.
What Gate Parts & Welding Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Hinge replacement | $150-$400 per hinge |
| Post replacement | $700-$1,800 |
| Custom welding repair | $250-$600 typical job |
Every price on this table is a written number you’ll have before we start, not after. We photograph each weld and each new part, and the photo record is yours at no additional charge.
Can you match the powder-coat finish on a Frisco HOA gate?
Yes. We keep a finish library of the common powder-coat colors specified by Frisco HOAs, and we can order an exact match for Stonebriar and Starwood gate styles when the original color code isn’t documented.
Do you replace a Frisco gate post if the pillar has moved a half inch?
Not always first. If the pillar is stable but the gate has shifted, we re-plumb the gate by shimming or re-hanging the hinges. If the pillar itself is moving with the clay cycle, we set the post on a deeper footer. We diagnose before we quote.
Brands We Service in Frisco
We service and repair gates built around Elite, Mighty Mule, LiftMaster, and FAAC operators, among others. We carry the common boards, remotes, and limit-switch parts for these brands on the truck, which means many Frisco repairs are completed the same afternoon the call comes in. See our brands for the full list of automation systems we work on.
Pricing for Gate Repair in Frisco, TX
| Service | Typical range in Frisco |
|---|---|
| Keypad replacement or repair | $180-$340 |
| Remote control addition or replacement | $120-$220 |
| Phone entry system repair | $200-$450 |
| Hinge replacement | $150-$400 per hinge |
| Post replacement | $700-$1,800 |
| Custom welding repair | $250-$600 typical job |
What pushes a Frisco access-control or welding price up is usually the clay-movement factor: when a post has shifted and the gate has to be unloaded, realigned, and re-plumbed before the electronics can be set, that adds time and material to the written quote. You’ll always know that number before we begin. There is no discovery invoice at the end of a Vance repair.
Neighborhoods We Serve in Frisco
We dispatch to every master-planned community in Frisco, from the gated streets of Starwood to the newest sections of Phillips Creek Ranch. Most Frisco neighborhoods are within a 20-to-35-minute drive of our dispatch point, and emergency calls are answered by a live person at any hour.
- Stonebriar
- Starwood
- Richwoods
- Phillips Creek Ranch
Service Area - Cities Near Frisco
We also serve the cities that share Frisco’s clay soil and HOA-governed gate stock. You’ll find the same written-price standard and photo documentation in Prosper, TX, Little Elm, TX, McKinney, TX, and Plano, TX. If you’re just outside one of those city lines, call us and we’ll confirm coverage directly.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Frisco
For most repair calls, we dispatch a technician the same day you call, and a live person answers the phone 24/7 at (972) 236-7089. The exact arrival depends on where in Frisco you are and what’s already on the schedule, but the response is measured in hours, not days.
Mostly no. Replacing a keypad, motor, remote, or hinge pin doesn’t change the gate’s appearance and won’t trigger architectural review. If the repair changes a finish or a panel pattern, we document the match for your HOA file so the review goes through cleanly.
In most cases no permit is required for like-for-like operator replacement on an existing gate. If the job involves new power runs or a new gate structure, your HOA may ask for documentation, and we provide a written scope and photo log for that file.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Frisco Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.